This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 10-21-2010, 04:25 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,162
simplyconnected is on a distinguished road
Default 430 Pistons MEL Engines

Quote:
Originally Posted by vernz View Post
Say Dave, Whenever you give advice about engine rebuilds you always talk about new pistons. I have a 430 and would dearly like to reuse my existing pistons. I believe the real issue is the cylinder condition from the standpoint of taper that has been worn into the upper end. Is there an acceptable amount of taper that would allow simple honing of the cylinder walls and reuse of pistons?

Vern
Regarding 430 MEL pistons... This topic has been addressed before, but I think it's time to revisit this issue.
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #2  
Old 10-21-2010, 04:49 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,162
simplyconnected is on a distinguished road
Default

Quote:
Originally Posted by simplyconnected View Post
Vern, I'd love to say, 'yes', but I can't. I was tempted to do just that until I learned about the consequences.

You described exactly what happens in a cylinder, it tapers. Installing new rings on a tapered bore will cause the rings to rapidly expand and contract, billions of times. It would work, but not for very long. In a short time, the rings would cause excessive piston groove wear and ring-top wear or they can break. Even if you tried setting the end gap at the bottom of the cylinder to .017" (at the smallest diameter), by the time the rings made it to the top, the end gaps would be open too much.

Old rings are half worn away, have less compression, and really don't flex with much outward pressure. The end gaps are about .100" wide, and the smooth cylinders cause them to hydroplane (and burn oil).

So, what are the options... You can bore and sleeve the cylinders. All aluminum engines have sleeves pressed into the bores, so this is a common practice. After honing the sleeves to the size of your old pistons, they would work just fine. I would do that if your 430 were mine.

Otherwise, a standard oversize bore and new pistons would be in order. I realize aftermarket pistons do not have the same contour as your stock pistons. If you get a group of owners together, you could probably convince a piston company to make a 'run' of pistons for the 430, but they would need to be all the same size. I will call my engine machine shop and ask how much sleeving costs.

But to answer your question directly; considering the cost of a major overhaul, using old pistons in the same bore is not worth it. Please realize, the used piston-to-used bore clearance is sloppy at .0025" (Ford's max limit). New piston in a new bore is spec'ed at .0015" (1-1/2 thousandths of an inch). The difference is only one thousandth.

By the time a typical engine is ready for an overhaul, the 'bell shaped' cylinder will be many thousandths wider at the top (you can use the 'ridge' as a witness mark for measurement).

Bottom line is... if you're spending that much to do a major, might as well do it once and do it right. Expect to spend around $1,500 for parts and machine shop costs. Then you assemble and install it, and save at least another $1,500.

Most of our squarebirders who restore their own engines, spend extra time to do things right. When done, their engines work even better than the production engine their Tbird came with. - Dave
I spoke with Mike (owner of my engine machine shop, D&S Engine Specialists), and he is confident that we can get correct pistons for the 430.

Mike is asking me to bring an original piston to him.
If you have an old 430 piston, please PM me.
I would like to borrow it, then I'd be glad to send it back if you need it.

I will find out what availability and cost would be for a new set. So, PM me if you have a piston to loan.

Mike said sleeving the engine is far too cost prohibitive, and I'm going in the wrong direction. He doesn't believe anyone should do a major using old, worn, pistions. All of his engines carry an automatic 2-year warranty, so you can understand why his shop uses premium components.
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #3  
Old 11-10-2010, 04:11 PM
P Jardine P Jardine is offline
Newbie
 
Join Date: Feb 4 2010
Posts: 5
P Jardine is on a distinguished road
Default

There has been a lot of discussion on pistons on the MEL engine forum, I have been part of that discussion. Although a number of manufacturers did make stepped pistons for the MEL series engines, most of them stopped based on demand. The pistons available from Kanter, Egge, and a few others are flat tops. This reduces the effective compression ratio from roughly 10:1 to about 7:1 and destroys the swirl in the combustion chamber further reducing performance. The 430 in particular was a VERY high performance engine with a short, yet fabled history. Ford paid particular attention to combustion chamber design, and piston style was big part of it.

In my particular build, which is a marine one, I ordered WISECO forged aluminum pistons with a 9.6 to 1 compression ratio. $1400 dollars. It was a fairly big investment, but overall in the big scheme of things.... not so much. My engine has been renewed completely with a 3 angle valve job, seats, new guides, crank was turned, Wiseco pistons, An original Mercury marauder intake with the 3 holley 2300's, Edelbrock M4 water cooled exhaust manifolds, Moon valve covers, etc etc. While cosmetics are important, a fresh engine costs for things you don't see, but they are the heart of the car/boat etc. I am looking forward to having an engine with a long life ahead of it, and no surprises or downsides.

If you visit the MEL engine forum, you will see a LONNNG thread on piston design etc.

Here are my Wiseco's and a couple of other pics of front and rear cover and polished manifold. Hours, I tell ya Hours.





Reply With Quote
  #4  
Old 12-04-2010, 04:35 PM
63-4drpost 63-4drpost is offline
Experienced
 
Join Date: Feb 14 2009
Posts: 159
63-4drpost is on a distinguished road
Default 430 togh as hell !!!

I paid $400.00 for a used 430,1959 model out of a t-bird. I lucked out as all it needed was a set of rings. i did install new lifters, and all gaskets and seals were replaced. (including valve stem seals) .Now I have been a certified ford tech for 45 years, and I know very well that to do it RIGHT, replace evrything. But I gotta say, this engine works very nice in my 1960 T-bird. Has tons of torque, and will run all day long in hot weather and never bothers at all. So in my case, I got by cheap! Sometimes a guy just gets lucky!!! I wanted to use the old but not worn out bearings because all I could find were Chineese replacements. I used Moly rings, seated right away. Point is, if you don't have the money for a complete overhaul, in an engine that is still within normal wear limits, go ahead and use the old pistons or bearings. Years ago, there were plenty of engine re-rung, valves ground, and put back together to go again, that's my 2 cents, probably isn't worth that to some.
Reply With Quote
  #5  
Old 03-15-2012, 05:59 AM
KULTULZ
 
Posts: n/a
Thumbs up

Quote:
Point is, if you don't have the money for a complete overhaul, in an engine that is still within normal wear limits, go ahead and use the old pistons or bearings. Years ago, there were plenty of engine re-rung, valves ground, and put back together to go again, that's my 2 cents, probably isn't worth that to some.
Correct. Piston wear and cylinder taper limits are given in the shop manual. While a completely fresh engine is nice, it is not necessary for a mild street engine.

The engines of this period are not as technically advanced as today's engines as far as machining and component tolerances.

Does anyone remember the piston ring ridge cleaning tool?
Reply With Quote
  #6  
Old 03-15-2012, 03:32 PM
vernz vernz is offline
Experienced
 
Join Date: Jul 12 2008
Posts: 185
vernz is on a distinguished road
Default

Not only do I remember the ridge reamer, I have one!

Vern
Reply With Quote
  #7  
Old 03-15-2012, 09:19 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,162
simplyconnected is on a distinguished road
Default

Quote:
Originally Posted by KULTULZ View Post
...Does anyone remember the piston ring ridge cleaning tool?
I think you are confusing two tools; a piston groove cleaner (to remove carbon deposits in the bottom of each piston groove) and a cylinder ridge reamer (to remove the cast iron 'step' at the top of each bore, left by ring wear).

I used to use a broken piston ring to clean carbon out of the grooves. After so many cuts, I found chemicals like phosphoric and sulphuric acids easily soften and remove carbon.

Vern has the ridge reamer because cylinder wear was so bad the pistons wouldn't come out of their bores. If the bore was that wide, it's time for a re-bore and new pistons (or sleeves). - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #8  
Old 03-31-2012, 03:38 PM
KULTULZ
 
Posts: n/a
Thumbs up

Quote:
Originally Posted by simplyconnected View Post

I think you are confusing two tools; a piston groove cleaner (to remove carbon deposits in the bottom of each piston groove) and a cylinder ridge reamer (to remove the cast iron 'step' at the top of each bore, left by ring wear).

-Dave
I am presenting confusing information. Your description of the two tools is more concise.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 08:42 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.